Guide Handbook Manual

Download

Hyundai manuals for 2000-2001 hyundai Accent installation manual Hatchback.
Hatchback: installation instructions
1. the Lower exhaust for ease of installation. 2. delete the cieplochronnej and cut out the corner closest to the hole that gets magnified, and then plug the heat shield. 3. raise the hitch to position and place 1/2 "carriage bolts to the safety chain plate above the vehicle tow loop and fasten your finger tight flanged 1/2" and spacer CM-SP34 as shown. 4. fasten the two bolts M12 with 1/2 "connical tooth mouse pads from existing weldnuts in the driver-side frame rail finger tight as shown. 5. Make a hole in the passenger side frame rail to fit 1/2 "bolts. 6. Fishwire 1/2 "carriage bolt with spacer CM-SP40 by rail passengers on the side of the frame from the edge of the bumper, the enlarged hole. Fasten your finger tight flanged 1/2 ". 7. the value of the moment, all the equipment 1/2 "to 75 ft-lb, and all of the M12 equipment to 65 ft-lb 8. Reattach the exhaust to the location of the hanger services removed in step 1.
Download

Honda manuals for 2004 Honda Accord Coupe Summary window module installation manual.
The Summary window module installation instructions:
1. Remove the driver side door panel (04 instructions Coupe) a., delete the take off the lid and 2 screws from the inside of the door handle of the Cup (b) remove the two bolts below the armrest c. Remove trim piece on the side of the mirror in the upper right corner of the door panel by pulling on it, died. gently remove the door panel by first pulling on it at the bottom and then fly over the window on the top lip e. unplug all cables and harnesses mechanical cables door panel door panel and place it in a safe place, f. Remove the speaker by inserting a screwdriver slot head flat on top and gently pulling on it. From the top, gently pull up on the loudspeaker, tap water released into free tabs bottom note: If you break one or two off the loudspeaker can easily be determined with the aid of a brief self tapping screws to secure the speaker to g. will find doors Behind the speaker wires, wire, primary for the door. It is recommended that the modules window to be securely attached to the wire ties or similar method. h. Green route cables in the module window for the wiring that plugs into the power window switches. Ideally this can be achieved by wire routing inside the door. If not possible, another option is to route cables from one of the holes, which clips the door panel, insert into, so long as the delete and reject the clip that goes into the hole. and all other tubes junction inside the door will, with the speaker.
Download

Ford manuals for 2000-2003 Ford Focus zx3/zx5 exhaust system setup guide.
Exhaust system: installation instructions
Remove the exhaust system: 1. using a saw or hacksaw cut stocks turning-pipe pipe Assembly just after the front silencer/front lines, as shown in Figure 1. 2. the application of cost-effective amount of spray grease to each set of installation/rubber Hanger, as shown in Figure 2, and then remove the two rear hooks with rubber mounts and pull for mounting the rear pipe/silencer from the vehicle. 3. remove the two screws securing the Assembly flange pipe muffler on the front of the catalyst. 4. remove all hooks with rubber mounts and pull the silencer pipe Assembly in front of the vehicle.The exhaust system installation: 1. place the front his new team at the flange pipe Borla performance vehicles. 2. Push the two hooks for rubber mounts and place two screws, nuts and washers, presented at the flange. Do not tighten two screws at this time. 3. place the screw end extended mounting of the silencer, and then place the mounting of the silencer pipe into the Assembly of the front, hooks the rubber push two mounts. DO NOT tighten the clamp. 4. Put a clamp on the enlarged end of the tailpipe and push the two hooks for rubber mounts. DO NOT tighten the clamp. 5. check exhaust system for proper ground clearance, and to adjust the tip. 6. once the positions of the two clamps Accuseal tighten properly between 32 to 35 ft. lbs. and two bolts securing the front pipe to the flange. 7. before you start your car, make sure you check all cables, hoses, brake lines, body parts and tyres in the safe clearance of the exhaust system. 8. Launch vehicle and check for any leaks. If the leak was found, determine the cause (eg. Clamp loose or incorrectly positioned) and repair if necessary.
Download

Dodge manuals for installation manual VSM G3 2008-2010 Dodge Avenger .
VSM G3 installation instructions:
Step 1. Place the DTT between console and frame moving chromium and is gently twist until the 4 clips you have in place. After the release of this frame, annul the contested and removed the front compartment cubby shifer. It is held in place with two (2) clips. Then the frame surrounding the meeting of the entire shift, cubby hole and the immediate area to the right and left control climate change must be removed. Remove this frame by placing the first DTT between the frame and the right control molding line of climate change. Gently work Open clips of four (4) holding the frame in the workplace right rotation clock utility to control climate change down around move and back up on the left side of the control of climate change. Carefully set aside this piece. STEP 2. Then remove the frame surrounding the radio. In the upper right corner of the frame right vent, include DTT. By gently turning motion clips for the release of eight (8) holding the frame in place, radio clockwise rotation. When you release the clips, unplug the wires to the frame of radio and carefully set aside. STEP 3. Remove the four screws (4) of torque, surrounding the radio of a torque T20. Delete radio, do not unplug the wires, protective wrap cloth around it and simply allow the radio to set aside.
Download

Corvette rear exhaust System installation/removal Manual.
Remove the exhaust system:
1. Loosen the clamps shown in Figure 1 is located just below the transmission at the rear of the vehicle. 2. using the socket 13 mm, unbolt the spring hangers, located at the front of the clamps. Place the screw for use during the installation of the new system, the exhaust system. 3. with a stand of the silencer or additional person have Assembly pipe h to position using Socket 15 mm flanges located just unbolt for catalytic converters. Place the seals on the equipment and on the side for use during the installation of the new system, the exhaust system. 4. Remove the Assembly pipe h with the vehicle by dropping the front than the rear sliding out at the factory by wiring harness/muffler axle. 5. using the spray type grease, lubricate hooks at the rear of the vehicle just above the tip assemblies. 6. Beginning with the driver's side of the vehicle, remove the hooks of insulators and the removal of rubber mounting of the silencer from the vehicle. 7. in the case of vehicles equipped with automatic transmissions, you must remove the heat shield on the side of the passenger from the fuel tank. Using a set of pliers or similar, the bend tab of the down. 8. Repeat step 6 to remove the mounting of the silencer on the side of the passenger. Download

Jaguar manuals for installation manual cylinder Hardtop Jaguar XKE 12.
Hardtop installation instructions:
A: before placing a Hardtop on car to: 1. fold the upper cloth into the normal position. 2. Clean the upper part of the windshield frame and rear deck area. 3. Lubricate the bottom rubber deck Hardtop with silicone grease or other suitable grease 4 remove knobs rear Velcro located directly behind the driver and front passenger seats 5 loosen the fixing on the Hardtop.
(B): Hardtop place on the car: 1. align the rear brackets on a Hardtop car mounting holes on the back. Insert the rear anchorages of the rear brackets Hardtop knobs by engaging the back of the mounting holes. Hand tighten the fasteners. 2. align the Hardtop on the windshield and install three hooks "J" in the windshield frame 3. Check the rear fasteners to make sure they are tight. 4. check the fit side for molding a Hardtop. Hardtop could be pushed forward or send backward better clearance side by removing the Hardtop and bending a rear mounting bracket in the opposite direction you want. Hardtop could be reduced by shimming rear bracket, where it installs to the hard top. 5. with a Hardtop, properly positioned and airtight Trim molding side excess.

Download

Hyundai manuals for 2007-2009 Hyundai Elantra Sedan receiver Setup Guide.
Instructions for installing a receiver:
1. unscrew the hexagon three screws from the plastic fascia included and remove the pieces of plastic from the tape. Apply pressure to opposite ends. Note: the Elantra and Rio 5 models only-Clip tab fascia included a socket. 2. the Lower exhaust of the vehicle in order to facilitate installation, removing rubber exhaust hanger services. 3. Raise hitch for the post, passenger side first. Rotate the position indicator on the outside of the frame rail. Pull gently, to disturb the fascia included. 4. raise the hitch on the driver's side, gently on the outside of the frame rail. Align the holes in the vehicle frame hitch openings on both sides. 5. install the equipment. Hand tighten the only until all equipment is installed. Note: due to the vehicle of the various configurations, will be the additional hardware left behind. 6. with all fasteners at the Center the hitch and tighten all M10 x 1.25 x 35 mm Hex CAP screws featuring # 2 to 40 pounds of torque (55N-m) and all of the M12 x 1.25 × 40 mm Hex CAP screws ft. # 4 to 75 pounds of torque (102N-m). Failure to Tighten the screws as specified may cause the loss of or damage to the fastener. 7. connect the exhaust hanger services locations (reverse step 2). 8. connect the fascia included tabs (reverse step 1).
Download

Honda Manuals for installation manual remote control engine Starter 2-door 2010 Honda Accord A/T .
Remote control of engine Starter installation instructions:
Note: this antenna should install only if the ambient air temperature of 15 ° C (60 ° F) or above. 1. make sure that you have the anti-theft radio code, then save the preset radio stations. 2. Disconnect the negative cable from the battery. Setting control 3. Using a small screwdriver flat tip fit switches in the control unit (Accessories) to the location shown. By using isopropyl alcohol on a towel shop, clean the area where the protective tape will attach control. Remove adhesive backing and include protective steering. Note: • choose switches occurred before the unit is plugged in. • If that switch settings is not correct, that the engine starting the remote will not work correctly. • If adjusting switches from the control unit, vehicle mounted, touch the metal part of the screwdriver to any metal parts of the vehicle to perform any static electricity. • If you change the settings for the switch from the unit connected, disconnect the unit again connect it before changing the settings. 4. remove the driver's dashboard lower cover (eight clips, two hooks and disconnect the vehicle). 5. the V6 model only: Remove the driver's dashboard screens (three clips and one pin).
Download

Ford manuals for 2008-2010 Ford Focus electronic trekking installation manual set.
Electronic Cruise Kit installation instructions:
A. suggestions before installation 1. It is recommended that you disconnect the negative battery cable for 3 minutes before starting the installation to avoid inadvertent airbag deployment. Note and record all the radio anti-theft code before hanging up. 2. remove the back lower driver's side and kick panels. Remove the Shroud of the steering wheel.
B. install electronic module 1. Connect the Main wiring harness, switch pedal interface wiring harness and the mating connector module Cruise Control. 3, Figure 2. Provides Cruise Control module in a secure location outside the driver's side of the line in the vicinity of the dam from the moving parts. Secure the supplied wire links. 3. Dear pipe interface pedal, steering column and the accelerator. 4. Locate the 6 pin and mate connectors on the pedal wiring interface. Remove Accelerator 6-pin mating connector and applied to the pedal interface cables. Other connector to the accelerator.
Download

Dodge manuals for 2007-Up Dodge Avenger QuickLIFT manual installation.
QuickLIFT installation instructions:
Step 1 – unpacking the system and check the contents of QuickLIFT. * (2) the gas Springs (RT-QLD-200-4A) – move them a few times before. * rivets (8) 3/16 "multi-grip # 1 (used in brackets, hood) * (4) ball Stud-mounting * colors instructions. Step 2-collect the required tool. You should collect the following utilities before you begin Setup: * Power drill * 3/16 "or # 11, indexed drill bits * Fine indelible marker or pen Pen * measure * the strap or ruler -weight masking tape * Hammer and center punch * rivet Rifle capable of rivets 3/16" (most brands can handle this size) Note: only by means of a system-supplied QuickLIFT nits. Step 3 – Mark stretch hood bracket locations. A. leave hood closed. B. using a piece of tape mask and indelible marker, accurately measure your Sweatshirt corner (near the hinges and windshield) and along the line of fender. Wrap the end of the tape measure and place it above the lip corner-weight masking tape to mark hood at 24-1/4. This mark will be used to align stretched the bracket ball-stud in the next step.
Download

C6 Guide Lt./2LT Hud installations Corvette.
Hud installation instructions:
Step 1: the radio console Surround Center and disposal: first you have to do this, remove the lid Center console. Odprawiana is in the four bolts T15 torx. You can remove a small plastic cover of the rear hold the nuts. The following illustration shows the console lid and nuts already deleted. Turning attention to the front of the console, eyes shift will need to be removed. Twist Tester plastic ring on the upper boot leather clock you e 35 degrees or so, and then Pull Up on the shift knob. You will need to use some of the forces here, but don't worry, not broke. It should be noted that I had to brake the car in neutral, but not e downloaded, I believe that it is necessary. To remove the emergency handle, pull down the skin and remove boot head screws Phillips. Pull-up handle shift to delete it. This took much more effort than I think that in this way. Then, remove the two screws on the right side of the console. Remove these screws 7 mm. towards the centre console there is another bolt to remove. To access, delete, select the cover by pulling the Ride up. I managed to do this manually, but you can use a screwdriver or a knife to help.

Download

Chevrolet/Chevy manuals for 2002 Chevrolet Avalanche Windshield installation/removal Manual.
Windshield installation/removal instructions:
The process of deleting: 1. delete all associated panels and components. 2. restore as much damage as possible to factory specifications. 3. Note the location and remove the following demands: sealers • sound deadeners • anti-corrosion materials are important: perform the sectioning under windshield 30? mm (1-3/16? inches) above the third hole trim Assembly. Important: careful not to damage the inner panels or strengthening. 4. Cut a pillar at the places where the sectioning to be executed. 5. Locate and drill out all the factories of welds. Note the number and location of weld installation portion of the service. 6. remove the damaged section of the Windshield pillar.
The installation procedure: 1. Cut a pillar replacement in suitable locations to match the rest of the original Panel. Cut shreds joint should be trimmed to a break of one and a half hours of metal thickness in removing common. 2. creation of 50? mm (2 inches) backing plate of the unused portion of the service. Trim for infusion poles so fit for removing common. 3. Perform additional procedures for removing as necessary. Refer to the Centre pillar of sectioning; Front lower pillar sectioning; Rear, Lock pillar sectioning; a Rocker sectioning. 4. Drill 8? mm (5/16?) holes to Plug, welding in the original part. Locate these holes around 13? mm (1/2 inches) from the cut edge of the shreds and the gaps between pieces of 40? mm (1-1/2 inches) apart. 5. Drill 8? mm (5/16?-inch) Plug weld openings Panel as necessary in the locations noted on the original Panel, and along the cut sectioning. CAUTION: FLAMMABLE FOAM SEALERS AND SHOULD BE REMOVED FROM ALL POINTS OF THE WELD.
Download

Cadillac manuals for 2003- 2006 Cadillac CTS automatic turning off traction control Kit installation guide.
Automatic turning off traction control Kit installation instructions for the system:
1. access to deck rear shelf where electronics rear body are located. Identify the module integration rear (RIM), as indicated in Figure 1. 2. references to figure 2 in connectors attached to the BCM, identify the following cables: Brown w/White stripe for 1 Connector (C1), Pin 1 connector on the A2 Pink (C1), Pin, A4 Black/White Connector 1 (C1), 3 Pin, A8. Using pliers, wire tap install, comes with a set to each of these three wires. 4. lamp volt meter or test to check whether the Pink slice to black with White stripe splice has 12 v, only when the ignition is turned on. 5. plug the connector wire Auto TCS Black wire to tap on a Black-White stripe. 6. connect the connector wire Auto TCS White wire to the tap at Brown-White stripe. 7. connect the Auto TCS Pink connector wire tap pink wire cables. 8. Secure module auto TCS with zip tie. 9. you must reinstall any under the rear panels removed. 10. This will complete the installation.
Download