Guide Handbook Manual

Ford manuals for 2000-2003 Ford Focus zx3/zx5 exhaust system setup guide.
Exhaust system: installation instructions
Remove the exhaust system: 1. using a saw or hacksaw cut stocks turning-pipe pipe Assembly just after the front silencer/front lines, as shown in Figure 1. 2. the application of cost-effective amount of spray grease to each set of installation/rubber Hanger, as shown in Figure 2, and then remove the two rear hooks with rubber mounts and pull for mounting the rear pipe/silencer from the vehicle. 3. remove the two screws securing the Assembly flange pipe muffler on the front of the catalyst. 4. remove all hooks with rubber mounts and pull the silencer pipe Assembly in front of the vehicle.The exhaust system installation: 1. place the front his new team at the flange pipe Borla performance vehicles. 2. Push the two hooks for rubber mounts and place two screws, nuts and washers, presented at the flange. Do not tighten two screws at this time. 3. place the screw end extended mounting of the silencer, and then place the mounting of the silencer pipe into the Assembly of the front, hooks the rubber push two mounts. DO NOT tighten the clamp. 4. Put a clamp on the enlarged end of the tailpipe and push the two hooks for rubber mounts. DO NOT tighten the clamp. 5. check exhaust system for proper ground clearance, and to adjust the tip. 6. once the positions of the two clamps Accuseal tighten properly between 32 to 35 ft. lbs. and two bolts securing the front pipe to the flange. 7. before you start your car, make sure you check all cables, hoses, brake lines, body parts and tyres in the safe clearance of the exhaust system. 8. Launch vehicle and check for any leaks. If the leak was found, determine the cause (eg. Clamp loose or incorrectly positioned) and repair if necessary.
Download

Ford manuals for 2008-2010 Ford Focus electronic trekking installation manual set.
Electronic Cruise Kit installation instructions:
A. suggestions before installation 1. It is recommended that you disconnect the negative battery cable for 3 minutes before starting the installation to avoid inadvertent airbag deployment. Note and record all the radio anti-theft code before hanging up. 2. remove the back lower driver's side and kick panels. Remove the Shroud of the steering wheel.
B. install electronic module 1. Connect the Main wiring harness, switch pedal interface wiring harness and the mating connector module Cruise Control. 3, Figure 2. Provides Cruise Control module in a secure location outside the driver's side of the line in the vicinity of the dam from the moving parts. Secure the supplied wire links. 3. Dear pipe interface pedal, steering column and the accelerator. 4. Locate the 6 pin and mate connectors on the pedal wiring interface. Remove Accelerator 6-pin mating connector and applied to the pedal interface cables. Other connector to the accelerator.
Download

Ford manuals for 2007–2008 Ford Focus bumper grille inserts manual Cover speed installation.
Bumper Cover speed grille inserts installation instructions:
1. raise the front of the vehicle to gain access to the back bumper of holes. 2. remove the apron ABS, thereby removing all fasteners securing to cover the bumper and the underside of the vehicle. You can find the "pushing" hex headed fasteners and screws. 3. Insert the Center grille opening the top speed for the Centre Party is fixed to the black plastic grid using two terminals on the cable. Insert the Cable tie loops gratings speed, and then through the X Member in a grid with plastic. Install the cable ties approximately 1 "from each end. Corner of the grille will speed fixed with two metal clips provided. Install the clips from "humped" side up. The clip will move through the grid x and on the grill. Clip as close as possible to each objective as possible. 4 speed side Grilles are installed in the same way. With the exception of air caused by side fairings grid failed to install cabling and terminals at the outer ends of steel clips. They will have to be installed to the apporximatley fixed 5 "from the extremities. 5. Pull all the terminals of the cables snug and cut off the excess. 6. reinstall the ABS apron removed in step 2.
Download

Ford manuals for 2005 Ford Mustang Roush przeciwmgielny wiring harness installation guide.
Fog lamp wiring harness installation instructions:
1. open the hood of the vehicle and remove black plastic Panel at the top of the radiator. 2. lay out Roush in the engine compartment, in accordance with the diagram below. 4. on the new harness, plug the Roush C2 and C4 Ford fog lights wiring. 5. Roush connector C1 and C3 to Ford fog lamps. 6. Roush C5 and C6 connectors to Roush fog lamps. 7. connect the ground on using existing wiring Roush bolt carrier core substrate Ford on the radiator. 8. using the screws (2) provided, attach the module pass Roush Tower push the rozpórke the driver's side. 9. Zip wires, cables, and Roush Ford hood release cable next to the Tower push rozpórke. 10. reinstall the black slab of plastic at the top of the radiator.
Fog light switch with Roush installation: 1. remove the front side and a liner of the front wheel the driver. 2. Route cables from the engine to the Roush grommet in a front wheel. 3. using cutters to cut the side of the nipple in the spare end grommet. Inserting single line L9 handsets through a hole in the nipple and insert the ½ "to convolute to the nipple. Place the zip tie around the nipple for pipe Roush on the spot. To harness the major postal bind Ford Roush harness. 4. reinstall the front side of the wheel well of linear and front wheel driver. 5. remove the installation of headlamp beam switch and disconnect the grey connector to Ford.
Download

Ford manuals for 2005 Ford focus 2.0 l nitrous Kit installation guide.
Nitrous Kit installation instructions:
1. by using standard removal tool can remove the stereo Ford, stereo. 2. unscrew the hexagon a/c controls, purchase ashtray, unplug the power loom and set aside the trim tile. Note When you extend each pipe. 3. measure 1 5/16 "down from the top of the trim audio unit and 1 1/8" in the driver's side as trim. Drill a hole 3/4 diameter switch, nitrous. 4. Cut square groove 1/16 "long on each side, on the left side of the hole. 5. install the Interior of the nitrous arming plunger to switch to the hole drilled in step 3. 6. connect the switch to the tip of the spade wiring to the back of the switch, the arming plunger: black wire to the top of the Brown terminal switch, red and blue wire from the middle and Red wire terminal on the lower terminal. 7. switch Route to harness the bulkhead by a dash down the back side of the driver's side of the fender well. 8. connect the wiring harnesses, reconnect the a/c controls, stereo and sound crop and replace the unit. 9. with the front of the car SAFELY on Jack stands, remove the front wheel on the driver's side. 10. Remove black bulkhead pipe molding from the location of the driver side fender well drill a hole in the corner ½ "outboard of the deleted region with plastic (molding).
Download