Guide Handbook Manual

Download

Jaguar manuals for installation manual cylinder Hardtop Jaguar XKE 12.
Hardtop installation instructions:
A: before placing a Hardtop on car to: 1. fold the upper cloth into the normal position. 2. Clean the upper part of the windshield frame and rear deck area. 3. Lubricate the bottom rubber deck Hardtop with silicone grease or other suitable grease 4 remove knobs rear Velcro located directly behind the driver and front passenger seats 5 loosen the fixing on the Hardtop.
(B): Hardtop place on the car: 1. align the rear brackets on a Hardtop car mounting holes on the back. Insert the rear anchorages of the rear brackets Hardtop knobs by engaging the back of the mounting holes. Hand tighten the fasteners. 2. align the Hardtop on the windshield and install three hooks "J" in the windshield frame 3. Check the rear fasteners to make sure they are tight. 4. check the fit side for molding a Hardtop. Hardtop could be pushed forward or send backward better clearance side by removing the Hardtop and bending a rear mounting bracket in the opposite direction you want. Hardtop could be reduced by shimming rear bracket, where it installs to the hard top. 5. with a Hardtop, properly positioned and airtight Trim molding side excess.

Download

Jaguar manuals for Bluetooth phone Setup Guide Jaguar X 308 .
Bluetooth phone setup instructions:
Basic stereo system connection factory in 1998 by 2002 XJ easy adapter for aftermarket website now handsfree Bluetooth. Remaining years and models are similar. Several have been successfully installed to take full advantage of Mute when calling the factory stereo line input to and output audio and mic factory. All required cabling there is in the centre console. Take a look at the schematic RT2 connector (connector 2-row white 10-pin). Pinout is as follows: RT2-1 = Purple/Red Audio from your phone to a stereo line level negative RT2-2 = Purple/Pink Audio from your phone to a stereo line level 3 positive RT2 = medium Purple/Orange radio and will switch the telephone audio music through the speakers. Most car sets fitted with wire to ground to mute so you can plug directly into the digestive tract. RT2-4 = yellow Factory mic positive lead RT2-5 = Braid Factory mic negative lead RT2-6 = Black ground RT2-7 = blue/yellow ACP networks of positive. RT2-8 = positive Brown/purple always powered battery fuse # 5 (5A) in fusebox RH heelboard. RT2-9 = ACP green/yellow light net negative. Note: a network of ACP is used for the functions of the radio button for the phone. RT2-10 = power White/Green Key switched fed fuse # 10 (5A) in the fuse RH heelboard. If you look on the face of the 10-pin connector, pin # 1 is in the left upper part and pin # 10 is in the lower right corner. The pins are numbered from left to right and top to bottom.

Download

Jaguar manuals for 2002-2006 Jaguar X-type Sedan the installation and user manual. Microphone, Argos installation instructions:
The procedure to install a microphone:
Gain access to the location of the 1. You will have to remove the overhead console, which houses the dome lamps Homelink control buttons, etc. Gently that all luminaires from the concert. 2. Microphone that mounted in the center console and snaps in place. 3. small black plastic suction mounts per page with one screw phillips. 4. Finally, connect the cable of the microphone to an overhead console. 5. Re-assemble an overhead console.
Argos Setup: to access the location of the 1. First thing, that is, you have to do is remove the drivers for the trunk (left) with shipping lines. You will then take trunk carpet. 2. unscrew the hexagon screws and remove the black plastic in a black plastic trim piece on the back of the trunk liner that was enough, from the hotel. Unscrew the hexagon black piece of trim on the floor on the left side (only to loosen it enough to bend back the liner). 3. There is a small plastic card, which helps you, hold the liner in place. This can be pried from the small screwdriver flat head. 4. remove the liner is bend it some, as this is quite flexible. 5. the arrow points to the Jack.

Download

Jaguar manuals for 1997-2000 Jaguar 4.0 LV8 engines installation methods Manual.
Installation instructions for the method:
The Committee AERATechnical offers the following information concerning the main bearing installation methods for 1997-2000 caution the Jaguar 4.0 LV8 engines. The camera uses three different screw thread sizes and improper torque is then, for some of the bolts, the lower end of the engine may result. Jaguar uses a bolts 34 possess the means of the cylinder block and there are four sizes of screws used. Method is installed, after the teams of the piston and the connector is installed and all the screws must be replaced after each use. To properly install method, follow the procedure listed below and refer to figure 1 below for locations suitable for attachment bolts. Step 1 install the "P" bolts and torque to 10-12 ft/lb step 2 installation "F" screw and torque to 18-19 ft/lbs step 3 Install "M" bolts and torque to 18-19 ft/lbs step 4 Install the "S" bolts and torque to 10-12 ft/lb step 5-6 torque, "M" screws for 25-27 ft/kg + 135 ° steps 7-8 torque's ' screws to 14-15 ft/kg + 150 ° torque step 9-10 "P" propellers to 14-15 ft/kg + 90 ° step 11-12 torque "F" screw to 14-15 ft/kg + 150 ° to complete the installation, each head screw Centre punch, after completion of the torque sequence.

Download